Vertex Standard VX-4000 Bedienerhandbuch PDF herunterladen (Seite 2)

Installation

AC Power Connection / Voltage Confirmation

The power supply in the BSC-5000 is capable of operation from

100 ~ 235 VAC at 50 or 60 Hz. The power supply in the BSC-

5000 does not require any transformer re-wiring, nor any chang-

ing of a switch position; the power supply will operate from ei-

ther 220 or 117 Volt line voltages without configuration changes.

This should be indicated by a label near the AC jack on the rear

panel. If no label is present, or if the AC voltage on the label is

different from the local AC line voltage, please examine the fuse

which is located near the AC jack for 100-117 V, use an 8 A fuse;

for 200-240 V, use a 6.3 A fuse.

Backup Power Supply

For uninterrupted operation during power failures, a 12 Volt

rechargeble type battery (55-Ah or more recommended) may be

connected to the BACKUP terminal posts on the rear panel.

When AC power is interrupted, the automatic power control cir-

cuit will automatically switch the BSC-5000 to the backup bat-

tery, and operation will not be interrupted.

After prolonged operation from the battery, it should be discon-

nected from the BSC-5000 and recharged separately before re-

connecting, as the trickle charge is not sufficient for recharging

a completely discharged battery.

Never reapply AC power to the BSC-5000 with a discharged

battery connected, as the DC start-up current can damage the

BSC-5000 and battery.

Lithium Battery Replacement

The BSC-5000's clock is run by a lithium battery. When the dis-

play becomes weak or clock operation ceases, it is time to re-

place the battery. The 3-Volt Lithium battery (P/N Q9000564) is

located on the top circuit board (RELAY Unit) of the BSC-5000.

1. Remove the 8 screws affixing the top cover, then remove the

top cover. Using your finger, slide the battery inward (you

will feel slight pressure by the mounting spring) then slightly

pry it up and outward so that it ejects freely through the

slots in the battery holder.

Transceiver Installation

The VX-4000/5500/6000 Mobile transceivers are all compatible

with the BSC-5000. Installation is simple and straightforward.

1. Remove the 17 screws affixing the top and bottom covers of

the BSC-5000, then remove the covers.

2. Turn the BSC-5000 upside down.

3. Use a sharp knife to make an "X" cut in the rubber cap, so as

to allow insertion of the antenna's coaxial cable.

5. Transceiver installation is now complete. Replace the top and

bottom covers.

Option Installation

Cooling Fan (FAN-1) Installation

1. Remove the 8 screws affixing the top cover of BSC-5000, then

remove the top cover.

2. Carefully note the battery polarity;

the positive (+) side (which includes

the battery model number) must be

facing up. Install the replacement

battery with the same polarity as when you removed it.

The Lithium Battery must be recycled or disposed of properly.

2. Pass the Cooling Fan's cable through the ventilation slot,

and connect it to the 2-pin jack (J1012) on the RELAY Unit.

3. Mount the Cooling Fan to the rear panel of the BSC-5000

using the supplied screws.

VEGA Tone-Remote Adapter Installation

1. Remove the 8 screws affixing the top cover of BSC-5000, then

remove the top cover.

2. Remove the panel from the VEGA 1223C Series Tone-Re-

mote Adapter and the VEGA 1224 Expansion Module.

3. Connect the VEGA 1223C Series Tone-Remote Adapter to

the Edge Connector which has the 5-pin Connector Cable,

then connect the VEGA 1224 Expansion Module to the other

Edge Connector.

4. Mount the VEGA 1223C Series Tone-Remote Adapter and

VEGA 1224 Expansion Module onto the chassis of the BSC-

5000, using the eight screws supplied with the CT-103.

5. Connect the 5-pin Connector Cable to J1014 on the RELAY

Unit, and connect the 12-pin Connector to J1013 on the RE-

LAY Unit.

6. Mount the Modular Jack on the rear panel of the BSC-5000

using the two supplied screws. You may choose either a 2-

wire or 4-wire Modular Jack.

7. VEGA Tone-Remote Adapter installation is now complete.

Replace the top cover.

J1012

to Cooling Fan

RELAY Unit

Antenna Coaxial Cable

Interface Cable

DC Cable

MIC Cable

Speaker Cable

Mounting Screws

(4 pcs)

VX-6000: Fit mounting screws here.

VX-4000/5000: Fit mounting screws here.

4. Install the transceiver into the compartment on the bottom

side of the BSC-5000, using the four supplied mounting

screws. Then connect the MIC Cable, Speaker Cable, DC

Cable, DSUB 25-pin Accessory Cable, and Antenna Coaxial

Cable to the transceiver.

Important Note: When installing the VX-6000 into the BSC-

5000, be careful to utilize the correct mounting screw loca-

tions (see illustration below). Tighten the screws using pli-

ers when installing a VX-6000.

Also, when installing the VX-6000, be sure to replace the

2-pin DC cable with the supplied 4-pin type.

Typical VX-4000/5500 Installation

Coaxial cable

Rubber Cap

Knife

Rubber Cap

FUSE 30A

BACKUP

INPUT

DC 10.8 - 13.2V

30A

POWER

ONOFF

FUSE 30A

BACKUP

INPUT

DC 10.8 - 13.2V

30A

POWER

ONOFF

VEGA

1223C Series

Tone-Remote

Adapter

RELAY-Unit

VEGA Tone-Remote Interface

Cable SET (CT-103)

J1014

J1013

2-WIRE: J1015

4-WIRE: J1016

VEGA

1224 Expan-

sion Module

4. Cooling Fan installation is now complete. Replace the top

cover.

1 2

Kommentare zu diesen Handbüchern

Keine Kommentare

Vertex Standard VX-4000 Bedienerhandbuch Seite 2

Kommentare zu diesen Handbüchern